Scrustie

Heb je een goed idee of ben je net met bouwen gestart? Laat het ons zien!

Moderator: Moderators

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Sat Oct 01, 2016 4:52 pm

Jeeej stapje dichterbij
Attachments
P1070872.JPG
P1070872.JPG (2.41 MiB) Viewed 16801 times
P1070871.JPG
P1070871.JPG (1.5 MiB) Viewed 16801 times
P1070870.JPG
P1070870.JPG (2.42 MiB) Viewed 16801 times
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

User avatar
maddox
Posts: 3631
Joined: Thu Aug 14, 2003 11:06 pm
Location: Vilvoorde
Contact:

Re: Scrustie

Post by maddox » Sat Oct 01, 2016 6:24 pm

Man, da's een look op zichzelf.

Maar zou je niet proberen voor grotere wielen nu?
Beter nu creperen, dan in de wars repareren.

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Sat Oct 01, 2016 7:51 pm

Misschien maar ik zou voor de rechter velg wel een nieuwe willen :) zit een gat in :(

De bouten bovenaan worden nog vervangen door kleintjes (blijven M12) maar zoals ik al eens eerder zei ben ik bang voor het gewicht, weegt een pak meer dan Kashei
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

User avatar
maddox
Posts: 3631
Joined: Thu Aug 14, 2003 11:06 pm
Location: Vilvoorde
Contact:

Re: Scrustie

Post by maddox » Sat Oct 01, 2016 8:40 pm

Nieuwe wielen is geen probleem, we zijn ondertussen een paar generaties verder.

En vergelijken met de lichte Kashei, die geen 12.5kg op de weegschaal zet da's minder dan optimaal.
Beter nu creperen, dan in de wars repareren.

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Sat Oct 01, 2016 8:48 pm

Juist RC wielen :) als je zegt de welke dat je zoal gebruikt dan kan ik eens rond kijken (eventueel met buddy code als je die nog hebt)
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

User avatar
maddox
Posts: 3631
Joined: Thu Aug 14, 2003 11:06 pm
Location: Vilvoorde
Contact:

Re: Scrustie

Post by maddox » Sat Oct 01, 2016 11:19 pm

We kopen de meeste wielen bij Conrad.

En de setup die jij hebt leent zich er niet zo gemakkelijk toe.
Beter nu creperen, dan in de wars repareren.

IBF
Posts: 18
Joined: Sun Apr 17, 2005 9:21 pm

Re: Scrustie

Post by IBF » Sun Oct 02, 2016 7:55 pm

Ik moet echt de handleiding van de 4_5 Esc doornemen want de error led pinkt
For your information: This LED is not really a error LED of the software, it is a hint for calibration the transmitter.
Background: When using the internal cross-mixing of the controller, it is necessary to set the stick of the controller "central".
Fail example: You have set the stick a little bit "left" of center. Therefore the controller for left/right means a little curve to the left, the right motor gets a little power. But the threshold (have a look on the motor-power-line) is not passed. => No reaction of the bot. => Ok

When you put the stick a little bit forward to move the bot, the power is set to both motors. But the right motor gets a little bit more power than the left motor. => At starting, the bot is doing a littel curve to the left.

An now, the yellow LED on the controller is needed: When the stick of the transmitter is exact centered, the LED did not blink.
When the input-channel 1 (for left/right) of the ESC is a little outside the center, the LED blinks one time.
When the input-channel 2 (for speed) of the ESC is a little outside the center, the LED blinks two times.
When the LED blinks three times, both channels are not centered.

This LED is a service to the roboteer, to "calibrate" the stick of the transmitter correct in centered position.

corresponding
30A fuse is electrofused
In princip, you can use a 40A fuse . But with the FK1-case, not available. => Prepare a fuse holder for the FKS-case and connect it to the FK1-case. => The MOSFET-halfbridges are made for 40A. :D
Only problem for you: You will need a little more "area" in the bot.

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Sun Oct 09, 2016 10:17 am

Juist terug van een nieuwe test sessie, veel meer tractie en controleerbaarheid maar de wielen zijn kut, dus nu gaat er een bestelling weg voor nieuwe wieltjes :)
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Sat Oct 15, 2016 12:56 pm

Jeej wielen, deze had ik nog liggen van den Action.
P1070873.JPG
P1070873.JPG (2.23 MiB) Viewed 16642 times
P1070874.JPG
P1070874.JPG (2.02 MiB) Viewed 16642 times
P1070875.JPG
P1070875.JPG (1.49 MiB) Viewed 16642 times
P1070876.JPG
P1070876.JPG (2.36 MiB) Viewed 16642 times
P1070877.JPG
P1070877.JPG (2.46 MiB) Viewed 16642 times
Heb alleen het probleem dat mijn 30A zekering blijft springen :( dat word dus de esc aanpassen zodoende dat die minder springt :mrgreen:
P1070878.JPG
P1070878.JPG (1.62 MiB) Viewed 16640 times
P1070879.JPG
P1070879.JPG (1.55 MiB) Viewed 16640 times
Ow en heb een weegschaal gekocht en Scrustie zit op 13.5kg +-0.1
IBF wrote:
Ik moet echt de handleiding van de 4_5 Esc doornemen want de error led pinkt
For your information: This LED is not really a error LED of the software, it is a hint for calibration the transmitter.
Background: When using the internal cross-mixing of the controller, it is necessary to set the stick of the controller "central".
Fail example: You have set the stick a little bit "left" of center. Therefore the controller for left/right means a little curve to the left, the right motor gets a little power. But the threshold (have a look on the motor-power-line) is not passed. => No reaction of the bot. => Ok

When you put the stick a little bit forward to move the bot, the power is set to both motors. But the right motor gets a little bit more power than the left motor. => At starting, the bot is doing a littel curve to the left.

An now, the yellow LED on the controller is needed: When the stick of the transmitter is exact centered, the LED did not blink.
When the input-channel 1 (for left/right) of the ESC is a little outside the center, the LED blinks one time.
When the input-channel 2 (for speed) of the ESC is a little outside the center, the LED blinks two times.
When the LED blinks three times, both channels are not centered.

This LED is a service to the roboteer, to "calibrate" the stick of the transmitter correct in centered position.

corresponding
30A fuse is electrofused
In princip, you can use a 40A fuse . But with the FK1-case, not available. => Prepare a fuse holder for the FKS-case and connect it to the FK1-case. => The MOSFET-halfbridges are made for 40A. :D
Only problem for you: You will need a little more "area" in the bot.
Lets try that shall we :) and on a second measuring I've got place for the XL version.
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Sat Oct 15, 2016 6:39 pm

Jee ik kon eindelijk mijn batterij oprijden en dat duurde niet lang :(

Filmpje:
Attachments
P1070881.JPG
P1070881.JPG (1.17 MiB) Viewed 16629 times
P1070880.JPG
P1070880.JPG (1.16 MiB) Viewed 16629 times
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

IBF
Posts: 18
Joined: Sun Apr 17, 2005 9:21 pm

Re: Scrustie

Post by IBF » Tue Oct 18, 2016 7:27 pm

Lets try that shall we :) and on a second measuring I've got place for the XL version.
:D

I have seen, that you have set two fuse-holder parallel. (correct seen?) . The yellow fuses are normally for 20A.
In my opinion, 2 fuses with 20A don't mean real 40A. => Like in the real life: One is the jackass, who has to work more like the other.... :wink:
(Or like in the cowboy-filmes: Two horses are not running in double speed like one horse. :D )

If you have the "area" in the bot, replace the new fuse-holder to a FK1-fuse-holder. In this case, it is possible to use the orange fuses (40A).

https://www.buerklin.com/de/kfz-sicheru ... r/p/46g720

for this fuse-type:
https://www.buerklin.com/de/kfz-flachsicherung/p/42g942

You are in Gent next weekend? I will bring you such a fuse-holder . :wink:

As you are able to sold on boards, to your information: This board of the ESC is made for two types of fuse-holder: FKS (like you got) and FK1 (see above). The only problem is: The fuse-holder for FK1 needs more space in high dimension. If enough space, you can replace the fuse-holder directly on the board.

Best regards
Reiner

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Tue Oct 18, 2016 8:24 pm

yes that's correct, I doubled them like they do in most car amplifiers.

Can you bring a upgrade kit to go from standard to xl, I think I got the room for it ;) I've got my soldering iron/desolderpump/solder packed.
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Sun Oct 23, 2016 6:20 am

Overlevingen van zaterdag:
1. zekeringen van de esc erdoor, zekering vervangen door een 40A
2. buiten de arena gewipt
3. wiel vast, dus kon alleen maar rondjes draaien
4. forfait wiel vast????

Ben eens benieuwd voor vandaag.
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

User avatar
Damic
Posts: 210
Joined: Wed Jul 27, 2016 5:56 pm
Location: Mechelen [BE]
Contact:

Re: Scrustie

Post by Damic » Sun Oct 23, 2016 7:51 pm

Deze morgend aangekomen en eens het wiel bekeken, het is erger het verhaal:
> Wiel gemonteerd en uitlijningsgaten (waar de vijzen doorgaat zodoende dat het wiel vast zit op het tandwiel) in de hdpe groter geboord zodoende date er meer spel is.
> Nope loopt nog altijd ergens aan
> wiel er terug af gedaan en zo alleen nog maar tandwiel op tandwiel overhouden
> Nope loopt nog altijd aan, maar wel altijd op dezelfde plek (voel je de bui al hangen)
> groot tandwiel eraf en draaien aan het tandwiel van de motor en ja hoor motor slag gehad en dus ergens binnenin iets scheef getrokken :(

Had ik het zaterdag geweten dan had ik nog aan Mario kunnen vragen om reserve motoren mee te brengen.

Swat was een leuke dag met leuke en minder leuke gevechten (pusher op pusher vind ik maar niets en meestal het publiek ook niet).
Ik kan vanalles en nog wat maar niets te goei, klinkt bekent??
Team CAD (Copy Adjust Destroy) :lol:

flex
Posts: 2711
Joined: Mon Jul 28, 2003 12:48 am
Location: Heerhugowaard
Contact:

Re: Scrustie

Post by flex » Sun Oct 23, 2016 9:37 pm

Botsen met HDPE raptors is het niet, nee. geen goed geluid uit te krijgen dan...
Niels Schotten
DRG Arena marshall & Judge

"Hard Work Often Pays Off After Time, but Laziness Always Pays Off Now."
Every once in a while you need to take your foot out of your mouth and up against your rear to kick our ass in to gear...

Post Reply

Who is online

Users browsing this forum: Ahrefs [Bot] and 53 guests