Toxic Twins, van Unskilledworker (Duitsland)
Moderator: Moderators
- leo-rcc
- Site Admin
- Posts: 5882
- Joined: Thu Aug 21, 2003 9:55 pm
- Location: Hoogvliet-Rotterdam
- Contact:
Toxic Twins, van Unskilledworker (Duitsland)
Dit zijn de Toxic Twins van Heiko (unskilledworker) uit Duisland.
Meer info en fotos zijn op het duitse forum te vinden:
http://forum.roboteers.org/thread.php?threadid=3871
type: raptor-cluster
gewicht: 2 cluster-delen, elk cluster-deel 3kg
wapen: Elk deel heeft een pneumatische 10-16bar-CO2-flipper
aandrijving: 16g CO2-patronen (een per cluster-deel)
pantser: veiligheidshelm met nog wat extra pantser
testrit: http://members.roboteers.org/unskworker ... tfahrt.avi
Ziet er best gaaf uit moet ik zeggen.
Meer info en fotos zijn op het duitse forum te vinden:
http://forum.roboteers.org/thread.php?threadid=3871
type: raptor-cluster
gewicht: 2 cluster-delen, elk cluster-deel 3kg
wapen: Elk deel heeft een pneumatische 10-16bar-CO2-flipper
aandrijving: 16g CO2-patronen (een per cluster-deel)
pantser: veiligheidshelm met nog wat extra pantser
testrit: http://members.roboteers.org/unskworker ... tfahrt.avi
Ziet er best gaaf uit moet ik zeggen.
Mvg,
Leo van Miert
Team RCC website.
Gentlemen, no fighting please. This is, after all, a council of war.
Leo van Miert
Team RCC website.
Gentlemen, no fighting please. This is, after all, a council of war.
-
- Posts: 13
- Joined: Tue Feb 14, 2006 9:36 am
- Contact:
'vuilophoping'=grip? i have only problems on the special floor in my girlfriends livingroom... the floor is oiled
@leo: thanks for the broadcasting...
btw: the white helmet was just a gag for my girlfriend... it was a testing-bot for her 'driving-license'
inside the bot under the akku is a steelblock of 1kg weight to get some weight on the axes for testdriving (total weight at this state with the steelblock: 1,9kg)
regards, heiko
the wheels are to soft for a steelbrush, but a toothbrush works well ... tested, but not yet build in permanently... i try to get one of the twins ready for the new-years-meeting ... much work to do till then, so no time for the 'fine-tuning' yettijd om ze een bbq-borstel te geven?
third time that i use 'pulling cilinder'... i like this way... its easy to build and gives a nice long fliparm... look at my album at the gra-forum, there are pictures of the testing-weapon and my raptor 'evolution'... it works the same way...leuke manier om daar je cilinder te plaatsen.
@leo: thanks for the broadcasting...
btw: the white helmet was just a gag for my girlfriend... it was a testing-bot for her 'driving-license'
inside the bot under the akku is a steelblock of 1kg weight to get some weight on the axes for testdriving (total weight at this state with the steelblock: 1,9kg)
regards, heiko
-
- Posts: 13
- Joined: Tue Feb 14, 2006 9:36 am
- Contact:
-estimated weight at the moment is 2,8kg for each cluster part. (gives a little bit space in weight for some 'extra stiffness' if needed...)
-the 1kg steelblock is was only for test-driving (see first pic in this thread)
the testbot only contained the (much to lage) akku, the speedos, receiver, drive (rs-390, 1,5€ each ) and of course the helmet
-so total weight at this state (first pic) without steelblock, pneumatics and armour was roundabout 1kg.
-the 1kg steelblock is was only for test-driving (see first pic in this thread)
the testbot only contained the (much to lage) akku, the speedos, receiver, drive (rs-390, 1,5€ each ) and of course the helmet
-so total weight at this state (first pic) without steelblock, pneumatics and armour was roundabout 1kg.
-
- Posts: 13
- Joined: Tue Feb 14, 2006 9:36 am
- Contact:
cylinder is a bore 40mm, stroke 53mm
roundabout 11,5 cm² bore-area, multiplied with 10bar to 16 bar gives 115kg to 184 kg...
force transmission is ca. 1:10, so 11,5kg at 10bar or 18,4kg at 16 bar...
theoretically
you can write in nederlandse taal... ik snap julie well...
see? my netherlands is much worse than your english...
feel free to write in your language... if i dont understand, i will ask
heiko
roundabout 11,5 cm² bore-area, multiplied with 10bar to 16 bar gives 115kg to 184 kg...
force transmission is ca. 1:10, so 11,5kg at 10bar or 18,4kg at 16 bar...
theoretically
you can write in nederlandse taal... ik snap julie well...
see? my netherlands is much worse than your english...
feel free to write in your language... if i dont understand, i will ask
heiko
Who is online
Users browsing this forum: No registered users and 49 guests